PRC ED-H 4 CUT OUT

Distributor - PRC ED-H 4 CUT OUT - 1079658 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Circular connectors (cable-side), Range of articles: PRC, Distributor, housing material: Polycarbonate fiber reinforced, color: black, nom. voltage: 400 V Your advantages  Time-saving Plug and Play installation with pre-assembled distributor boxes  Locking mechanism can be unlocked manually or using a tool  Ideal for indoor and outdoor use due to weatherproof materials  Customer-specific versions and assembly available on request Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626801018 Technical data General data Color black Locking type Snap-in locking Width 129 mm Height 129 mm Length 77 mm Connection data Nominal voltage ATD 400 V Degree of protection IP66/67/69 Material data Contact surface material Silver Housing material Polycarbonate fiber reinforced 05/12/2020   Page 1 / 3 Distributor - PRC ED-H 4 CUT OUT - 1079658 Technical data Material data Seal material TPE Material of locking screw Polycarbonate, fiber-reinforced Cable gland material PPE Color of the housing part black Knurl material PPE Ambient conditions Ambient temperature (operation) -40 °C ... 70 °C (Depending on the current carrying capacity/derating curve) Ambient temperature (storage/transport) -40 °C ... 70 °C Ambient temperature (assembly) -5 °C ... 85 °C Standards and Regulations Flammability rating according to UL 94 V0 Safety note • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products 05/12/2020   Page 2 / 3 Distributor - PRC ED-H 4 CUT OUT - 1079658 Technical data Standards and Regulations • Operate the connector only when it is fully plugged in. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com PHOENIX CONTACT ROMANIA Splaiul Unirii 165 Timpuri Noi Square TNO1, Etaj 1 Bucuresti 030133 Romania +40 21 350 88 12 - 3 +40 37 448 56 32 - 7 http://www.phoenixcontact.ro 05/12/2020   Page 3 / 3